Відео

2 minutes in and still babbling

Hello brother, I want to talk with you?? How it is possible??

Hi Nice video. Just wanted to know if we can controll the speed of an Exhaust fan motor with a regulator

for the calculations of amperage should I take the maximum or the rated amperage of the loads?

Thank you very much for this explanation!!

Not as common as it once was? USB still quite common, but perhaps you mean RS232 and similar? Thx for the video.

Ask Dali crew why terminal blocks are important

Outdated way to teach. Just pointless talking. Modern pedagogy is wasted on this channel

Thanks Sir

I am here for the methods of AC Motor speed control not covered in this video.

How do we calculate the wire size for interconnects? I have a large Ah 24v battery bank I'm putting together but don't know what size wire to use. Been searching....

Thank You. I am new to serial communications and this was helpful. Especially the baud rate/bit rate visual.

As I understand it, a dc relay coil is only polarized if it includes a diode. Otherwise, you can swap the leads with no problem.

Instalasi listrik power suplai

Both of the relays shown were electromechanical. Read the side of the relay at 2:27

Hi do you have a topic about , Wire Duct Divider?

Have you a handy dandy Automotive fuse 5v and wire it to the former so nothing trips or blows stormer itself a

I was on the edge of my seat so much that I fell off. Now I’m watching from the floor and it’s still epic.

Do you ever get that new gadget smell? Asking for a friend.

it sounds like something is in his mouth

goodbye josh :(

Which would be the best material for pipes in outdoor installation (exposed to sun,rain etc) PVC or HDPE ?

Fascinating video. ❤️ the safety

Beware beware beware. Got a few that had no gas tubes inside just a couple small screws on the sides. No protection at all. Got ones with flush screws and some labeled 230v with big bulging screws. Tested them with a 0-230v supply with a 20k protection resistor. Big surprise. The flush screw ones were 230v rather than 90v so checked the tubes. Yep 2r230's. Some sold at 90v had 230v tubes. The ones with big screws have double gas tubes rated at 230v but the tubes are meant for a center ground so 460v end to end. Bad news for most radios. So far only 1 of 8 have had what they were sold as. Beware the big bulging screw ones and check the small inset screw ones.

Graphics would have helped how do u determine the load and line side of a breaker. What about other components

It would be nice to see it closer up or some highlight lines to show what he is talking about like on the ground block

The question is How if the landlord leave their home and there is no home's load used while landlords leave their home at all and all batteries is fully charged? Where does the solar panel energy will go or delivered when a daylight time and solar panel within produce the energy condition? Anyone can help to explained to me please?

Do you have book on Earthing subject in pdf format? Very useful knowledge. 👍🏻

ماشاءاللہ بہت خوب ❤ So super instruction ❤❤

And i use the two 12v 9a in series and the 3 12v 100ah in parallel and add the negative to the negative and the positive to the positive to get 24v 309ah

Please if i have 2 12v 9ah and 3 12v 100ah and i need 24v 300ah and on going how do i wire 😢the batteries 🔋 to get the 24v 300ah and more

Excellent video!

Video sucks

How do I find what kind of speed sensor my electric motor has.

By far this is the best Explanation I have seen on UA-cam!! Thank you so much for this clean clear explanation 👏🏽

wow

thank you very much you make easy to understand relay

you are so amazing ,i learn a lot of thing

This man looks like J-mac. If you know you know.

Electrical troubleshooting is a systematic process to identify and resolve electrical issues. It involves following specific stages to ensure the problem is addressed effectively and safely. Here are the basics of the troubleshooting stages: 1. Gather Information: Start by understanding the problem. Ask questions like when the issue began, if it occurs consistently, and if there are any related symptoms. This information will help you narrow down potential causes. 2. Safety First: Always ensure your safety by turning off the power source before starting any troubleshooting. Use appropriate personal protective equipment like gloves and safety glasses. 3. Visual Inspection: Perform a visual inspection of the electrical system. Look for loose connections, burnt components, or damaged wiring. This step can often help you identify the issue without needing advanced testing. 4. Testing and Measurements: Use appropriate testing tools like a multimeter to measure voltage, current, and resistance. Compare your readings with the expected values to determine if there are any abnormalities. 5. Identify the Problem: Based on your findings, identify the root cause of the issue. This could be a faulty component, incorrect wiring, or a loose connection. 6. Repair or Replacement: Once you've identified the problem, proceed with repairing or replacing the faulty component. Make sure to follow the manufacturer's guidelines and safety precautions during this process. 7. Verify the Solution: After repairing or replacing the faulty component, retest the system to ensure the issue has been resolved. If the problem persists, you may need to repeat the troubleshooting process. 8. Document and Learn: Keep a record of the issue, its cause, and the solution. This documentation can help you in the future if similar problems arise. It also allows you to learn from your experiences and become more proficient in electrical troubleshooting. Remember, electrical troubleshooting can be dangerous if not done correctly. If you're unsure about any step or feel uncomfortable with the task, it's best to consult a professional electrician.

The software is terrible when compared to AB’s RSLogix. So little is streamlined it’s remarkable.

Nice video ❤

Thanks

👍👍

This was helpful. Danke schon

I’m working at maverick power I learn a lot and understand more in this Video thanks

❤❤❤🫶👍

❤️❤️❤️❤️🫶✊

Volume's horrible, keeps going lower and lower....

Is there difference in battery charging between : two batteries in series wired parallel and two batteries in parallel wired in series? In both way you got same result, but in other scenario + + and - - are common (but in the first scenario like one in video, + / - and another + / - aren't connected.